Laisse TigerStop Europe adapter votre scie à format, pour que vous pouvez travailler plus vite et plus précise que jamais.

Steps 6-8

6 Install the Pusher Shaft and connect the Fence Bracket. Thread one of the nuts on to the 1/2" pusher shaft until it cannot be threaded any farther. Insert the unthreaded end of the shaft into the carriage hinge from the right until the nut stops it. Thread the other nut on to the shaft until it stops. Firmly tighten the nuts to hold it in position. Slide one blue bracket block over the long end of the pusher shaft until it contacts the nut, and tighten it down using the set screws. Push the carriage left until the bracket block can intersect the fence bracket. With the fence bracket inserted into the slot in the bracket block, tighten down the set screws to secure it. At this point it may be necessary to pivot the TigerRip Fence in order to achieve the right angle to create a viable link.

7 Install the Pneumatic Cylinder assembly. Install the second bracket block, which serves as the cylinder bracket, by tightening it down to the outside edge of the fence bracket. Slide the cylinder adjustment shaft into the hole in the bracket block, and tighten down the set screws. Mount the pneumatic cylinder to this shaft, with the air lines leading to the right. Rotate the pneumatic cylinder to upright position and link the shackle to the existing rip fence locking handle. Be sure that the locking handle and the shackle intersect at the correct angle to provide effective and secure link-age. As shown in the picture, the TigerRip Fence may have to be pivoted to achieve this. The rip fence locking handle must be able to reach its locking position when pulled down by the pneumatic handle shackle as shown in the picture. If the long end of the pusher shaft interferes with this, disassemble the brackets from the shaft, mark the shaft where it must be cut off, and hacksaw the excess length. Then reassemble the brackets to the shaft and the pneumatic cylinder, and make sure the handle can now lock down.

8 Initialize the TigerRip Fence and make final adjustments. Make sure that the red Power switch is OFF. Make sure the air supply is connected to the regulator. Plug in the controller cable to the motor box and to the controller (plug with RED dot to the controller). Plug the interlock into the round port next to the controller cable port. Plug the TigerRip Fence into a surge-protected 110 outlet. DO NOT POWER UP UNTIL ALL CABLES ARE PLUGGED IN!

When initializing your TigerRip Fence for the first time, disconnect the handle shackle and lift the locking handle to unlocked position. When the fence is stationary (not moving), the pneumatic clamp should pull the shackle down (locked position); when moving, the clamp should be expanded to unlock position. If the opposite happens, unplug the air lines at the clamp and reverse them. If the fence does not move smoothly, apply graphite or wax to the table and the guide bar. When you are satisfied that TigerRip Fence is moving your existing fence, reconnect the handle shackle, and try it again. When stopped at a target value, manually try to lift up on the locking handle. It should be very difficult to do. If it lifts easily, you must increase air pressure at the regulator. Adjust the Air Pressure at the Regulator. Pull down on the dial at the bottom of the regulator to unlock it, and revolve until you hear the air pressure increase. Repeat this process until the locking handle is being pulled down securely enough to prevent drift. The regulator comes with an instruction sheet of its own, shown in the picture on page 1. When everything is operating correctly, make sure that all fasteners are properly tightened down, and then you are ready to use your new TigerRip Fence!

The TigerStop, Inc. TigerRip Fence Universal Adaptor Kit is designed to easily automate an existing rip fence with a minimum of modification. However, for certain models of saws there may be some on-site modification necessary such as, but not limited to, drilling and tapping of holes in the existing equipment or the TigerRip Fence components. Never drill and tap holes in the TigerRip Fence extrusion (the fence beam) itself, as this may damage the drive system. TigerRip Fence must be installed in accordance with all local, state, and federal regulations, as well as common sense safety requirements. Use only trained professionals when installing TigerRip Fence with existing equipment to ensure a safe and proper work station that will in no way endanger the operator or any other personel. Do not operate TigerRip Fence without proper training, both in TigerRip Fence operation, and in the operation of the saw itself.

Page Prochâine>

page 1 | page 2 | page 3 | page 4 | page 5

Charger en format PDF